How many pavers do I need for a 10×10 patio?
A 10 × 10 ft patio is 100 square feet. In standard 4 × 8 in pavers that is 460 pavers with 7 percent waste, or 105 pavers if you use 12 × 12 in. Under them you need 1.36 cubic yards of gravel (2.0 tons) for a 4 in base, 0.34 cubic yards of bedding sand, 2 bags of polymeric sand, and 5 pieces of edge restraint.
Paver count for a 10×10 patio by paver size
| Paver | Pavers to buy (7% waste) | Pavers per sq ft | Polymeric sand |
|---|---|---|---|
| 4 × 8 in Holland | 460 | 4.30 | 2 bags |
| 6 × 6 in | 411 | 3.84 | 2 bags |
| 6 × 9 in | 276 | 2.58 | 2 bags |
| 12 × 12 in | 105 | 0.98 | 2 bags |
| 16 × 16 in | 60 | 0.55 | 2 bags |
| 24 × 24 in slab | 27 | 0.25 | 2 bags |
Counts assume 1/8 in joints and 7 percent waste for edge cuts. Base gravel, bedding sand, and edging are the same whichever paver you pick.
Change the numbers
The calculator below is preset for this size. Adjust anything and the results update instantly.
Base, sand, and edging for a 10×10 patio
- Gravel base: 1.36 cubic yards of 3/4 in minus crushed stone for a 4 in base, about 2.0 tons. On clay or a wet site, go 6 in deep: 2.04 cubic yards.
- Bedding sand: 0.34 cubic yards of coarse concrete sand, screeded exactly 1 in thick. That is about 18 bags of 50 lb if you buy bagged.
- Polymeric sand: 2 bags of 50 lb for 1/8 in joints with 4 × 8 pavers; large-format pavers need less because there is less joint.
- Edge restraint: 5 pieces of 8 ft plastic edging and about 20 10 in spikes. Skip the sides that butt against the house.
- Excavation: dig 7.4 in below finished grade for base, sand, and a 2-3/8 in paver, which is about 2.3 cubic yards of soil to haul away.
What a 10×10 paver patio costs
Materials for a 100 sq ft patio run roughly $360 to $625: basic concrete pavers at $2 to $4 per square foot, gravel at $45 to $65 a ton delivered, sand, polymeric sand, and edging. Natural stone or large porcelain slabs push the paver line to $8 to $15 per square foot. A contractor-built patio of this size typically prices at $1,200 to $2,200 installed. Renting a plate compactor and a wet saw for the weekend adds $100 to $200 to a DIY job.
Common questions
How many pavers do I need for a 10x10 patio?
460 of the 4 × 8 in Holland pavers, 276 of 6 × 9 in, 105 of 12 × 12 in, or 27 of 24 × 24 in slabs, each with 7 percent extra for cuts.
How much gravel goes under a 10x10 paver patio?
1.36 cubic yards, or about 2.0 tons, for a 4 in compacted base with 10 percent for compaction. Use 6 in (2.04 cubic yards) on clay soil or where water collects.
How much sand do I need for a 10x10 patio?
0.34 cubic yards of coarse concrete sand for the 1 in bedding layer, plus 2 bags of polymeric sand to sweep into the joints after the pavers are set.